News

What Is Related To The Mixing Performance Of A Single-shaft Dry Mortar Mixer

Oct 12, 2025 Leave a message

1. Structural Design of the Mixer (Core Determinant)

The structural design directly affects the "contact efficiency" and "shear/mixing intensity" between materials, which is the fundamental factor determining mixing performance.

(1) Structure of the Mixing Shaft and Agitator

The mixing shaft is the core moving part, and the design of the agitator (attached to the shaft) is critical:

Agitator Type: Common types include paddle-type, plow-type, screw-type, and comb-type.

Paddle-type agitators: Suitable for general dry mortar (e.g., masonry mortar), with large stirring range but limited shear force.

Plow-type agitators: Stronger material turning ability, suitable for mortars with uneven particle sizes (e.g., thermal insulation mortar containing lightweight aggregates).

Screw/comb-type agitators: High shear force, ideal for mortars requiring fine mixing (e.g., tile adhesive with additives like cellulose ether).

Agitator Arrangement: The angle, spacing, and spiral direction of the agitator determine material flow. For example, staggered arrangement of paddles (30°–60° angle) can avoid "dead zones" (areas where materials are not stirred) and promote horizontal/vertical circulation of materials.

Shaft Speed: The diameter of the mixing shaft and the linear speed of the agitator (related to shaft speed) affect mixing intensity. Excessively high speed may cause material "flinging" (materials stick to the tank wall due to centrifugal force), while excessively low speed leads to insufficient mixing.

(2) Mixing Tank Structure

The tank's shape and internal design determine the flow path of materials:

Tank Shape: Most single-shaft mixers use a U-shaped or semi-circular tank. This design matches the agitator's rotation trajectory, minimizing dead zones. A poorly designed tank (e.g., sharp corners) will trap materials, resulting in uneven mixing.

Tank Liner Material: The liner (in contact with materials) affects wear resistance and material adhesion. Common materials include high-manganese steel (wear-resistant, suitable for abrasive aggregates like quartz sand) and polyurethane (anti-adhesive, suitable for fine powders like cement). Severe liner wear will change the tank's internal structure and reduce mixing uniformity over time.

Dead Zone Control: Some advanced mixers add auxiliary scrapers or side agitators at the tank's bottom or sides to eliminate dead zones (e.g., the gap between the agitator and tank wall), which is especially important for mortars with high powder content.

(3) Feeding/ Discharging Port Design

Unreasonable feeding or discharging will disrupt material mixing continuity:

Feeding Port: Multiple feeding ports (for aggregates, cement, additives) should be evenly distributed along the tank's length to avoid localized accumulation of a single material. For example, if all cement is fed at one point, it may clump before mixing with aggregates.

Discharging Port: The port should be large enough (matching the mixer's capacity) and located at the tank's lowest point to ensure rapid, complete discharging. A small or improperly positioned port will cause material residue, which mixes with the next batch and reduces product stability.

Single Shaft Dry Mortar Mixer

2. Material Properties (Raw Material Constraints)

The physical and chemical properties of dry mortar raw materials directly affect mixing difficulty and uniformity:

Particle Size Distribution: If the particle size difference between materials is too large (e.g., 5mm aggregates mixed with 0.01mm cement powder), segregation is likely to occur during mixing or discharging. Adding medium-particle-size materials (e.g., fly ash) can improve compatibility.

Material Density: Materials with large density differences (e.g., lightweight ceramsite with density 600 kg/m³ and quartz sand with density 2600 kg/m³) are prone to stratification during mixing. Slower mixing speed and longer mixing time can mitigate this.

Moisture Content: Excessive moisture (>5%) in aggregates or cement will cause clumping (e.g., cement hardens into small lumps), which cannot be broken by the mixer, leading to uneven mortar. Raw materials should be pre-dried to control moisture below 2%.

Powder Fluidity: Fine powders (e.g., talc powder) with poor fluidity are easy to agglomerate, requiring agitators with high shear force (e.g., comb-type) or adding anti-caking agents (e.g., calcium stearate).

3. Auxiliary System Configuration (Supporting Factors)

Auxiliary systems provide guarantees for stable mixing performance:

Dust Removal System: Dry mortar produces a lot of dust during feeding. A poorly designed dust collector will cause negative pressure in the tank, affecting material flow and leading to uneven feeding.

Lubrication System: The mixing shaft and bearings need regular lubrication. Insufficient lubrication will cause shaft speed instability (e.g., intermittent slowdown), resulting in uneven mixing.

Control System: An intelligent control system (e.g., PLC control) can accurately adjust mixing time, feeding sequence, and shaft speed, avoiding human operation errors. For example, automatic timing of mixing time ensures consistency between batches.

Send Inquiry