1. Pre-Operation Preparation
Before starting the mixer, thorough checks and preparations are essential to prevent malfunctions and ensure safety.
Equipment Inspection
Check the double mixing shafts and blades for wear, looseness, or damage. Ensure blades are securely fastened and aligned to avoid uneven mixing.
Inspect the drive system (motors, reducers, belts, or chains) for proper lubrication, tension, and absence of abnormal noise.
Verify that the discharge door/valve operates smoothly and seals tightly to prevent material leakage during mixing.
Check electrical components (switches, cables, sensors) for damage or loose connections. Ensure emergency stop buttons function correctly.
Material Preparation
Confirm that raw materials (sand, cement, additives, etc.) meet quality standards and are free of large impurities (e.g., stones, clumps) that could damage the mixer.
Prepare materials according to the 配方 (recipe), ensuring accurate proportions for consistent mortar quality.
Clear the mixing chamber of any residual material from previous batches to avoid cross-contamination.
2. Startup Procedure
Follow a strict sequence to start the mixer safely and ensure proper operation.
Power On
Turn on the main power supply and check that all control panels and indicators function normally.
Idle Run Test
Start the mixer in empty mode (without materials) to verify:
The mixing shafts rotate smoothly in the correct direction (usually counter-rotating for optimal blending).
There are no abnormal noises, vibrations, or friction between components.
The discharge door opens and closes properly.
Run the idle test for 2–3 minutes; stop immediately if any issues arise and troubleshoot.
3. Material Loading & Mixing
Proper loading and mixing parameters are critical for achieving uniform mortar.
Material Feeding
Load materials into the mixing chamber in the recommended order (typically: aggregates first, then binders like cement, followed by additives). This prevents dust accumulation and ensures even distribution.
Use feeding equipment (e.g., screw conveyors, belt conveyors) to control the loading rate, avoiding overfilling which can strain the motor or reduce mixing efficiency.
Setting Mixing Parameters
Adjust the mixing time based on the recipe (usually 3–10 minutes, depending on material type and batch size). Longer mixing times may be needed for mortar with additives requiring thorough dispersion.
Monitor the mixing process via observation windows or sensors to ensure materials are blended evenly.

4. Monitoring During Operation
Continuously supervise the mixer to detect issues early and maintain quality.
Key Observations
Check for uniform material consistency: Uneven mixing (e.g., clumps, segregation) may indicate blade wear, incorrect rotation speed, or improper loading.
Monitor motor temperature and current: Overheating or excessive current suggests overload; stop immediately to avoid motor damage.
Ensure no material leaks from the discharge door or feeding ports.
5. Discharge
Once mixing is complete, discharge the mortar efficiently while minimizing waste.
Stop Mixing & Open Discharge Door
Pause the mixing shafts (or reduce speed) before opening the discharge door to prevent material splashing.
Open the discharge door gradually and ensure all mixed mortar flows out smoothly into the collection container (e.g., a hopper or conveyor).
Cleaning Residual Material
After discharge, run the mixer briefly in empty mode to clear any remaining mortar from the chamber and blades, preventing caking or corrosion.
6. Shutdown Procedure
Proper shutdown protects the equipment and ensures readiness for the next use.
Stop the Mixer
Close the discharge door and stop the mixing shafts.
Turn off feeding equipment and ensure no more materials enter the chamber.
Power Off
Switch off the control panel first, then disconnect the main power supply.
Post-Operation Cleaning & Maintenance
Clean the mixing chamber, blades, and discharge area thoroughly to remove mortar residues.
Lubricate moving parts (bearings, shafts) as per the manufacturer's recommendations.
Inspect for wear or damage again and record any issues for repair.
7. Safety Precautions
Never open the mixing chamber or reach into it while the mixer is running.
Ensure operators wear appropriate PPE (safety helmets, goggles, dust masks, gloves).
Post warning signs near the equipment to restrict unauthorized access.
In case of emergencies (e.g., jamming, overheating), press the emergency stop button immediately.
